• When you first bought your home you probably invested in a standard six sided socket wrench set. The most common nut around the house is the six sided (hex) nut that you find everywhere in your house. Products you bought and have had to assemble have also had the hex nut so you’ve gotten a lot out of your socket set. After you’ve been in your home for a few years you have most likely bought appliances with small engines. You may have a lawn mower, gas weed trimmer, tiller, small gas chain saw, maybe a snow blower. IF you’re like most people you’d like to save some money by doing some maintenance and minor repairs on those small engines yourself. You’ve check owner’s manual on the internet and gotten direction on how to change filters or adjust carburetors and throttles. It really is something you can handle. You’ll need to follow directions and take notes on how to reassemble the small engine but a lot of this you really can do yourself.

    Now you’ve decide to start tackling that small engine repair. The socket set you’ve got will be very useful along with stander flat head and Phillips head screwdrivers. But you’ll find you need to get into to some hard to reach areas, and also you start seeing nuts and screws that you’re not familiar with at all. What do you do now? Simple, go to your local hardware store and tell them what you’ve run into. Sketches are good to take along with you when you go, and with your description of the screw head or funky nut you’ve found the hardware people will be able to help you with just about anything you’ve encountered. They’ll take you over to screw drivers, wrenches, and the socket wrench sets to help you find what you need. But you don’t need to buy entire sets of hand drivers and screw drivers. There are a number of screw bit, and sockets that you can use with the ratchet wrench in the socket set you already own.

    These accessories to a socket set are a great way to go and more economical in the long run. You can get low profile flat head and Phillips screw driver bits, along with bits for screws you’re not familiar with. Same thing with any different kind of nuts you run into, you’ll find sockets that will fit your socket set’s ratchet. You may also need extenders of varying length to get into those hard to reach areas. You’ll be surprised at how they put that engine together and may need deep well sockets not standard in most socket sets to get at some nuts or screws. Don’t forget to buy spark plug sockets for your socket set. They usually come in sets of three, to change car and small engine spark plugs and should be all you need for any spark plug you run into.

    You may want to buy the entire socket set or bit set they recommend so you have an array of sizes. But one or two sizes may be all you need, and you can just add them to the socket set you already have. Small engines are usually pretty simple so most people can work on them themselves instead of taking them to a professional, and having fixed it your self is a great feeling. Remember to wear eye protection and have a clean work bench, this will also make it a safer way to work.

    Article by Elizabeth
    If your interested in seeing a variety of bits and specialty sockets please visit our web site http://www.socketsetsandmore.com

    Article Source:
    http://EzineArticles.com/?expert=Elizabeth_Vinje

    Comments Off
  • Overview and Features of Elementary/ Middle School Career Development Models

    Counselors and teachers know that the elementary/ middle school development is important. Schooling is a time of transition, a threshold to the student’s future, and a bridge into the student’s destiny. In elementary/ middle school, career development is a time to build career awareness, not a time for premature career choices or career preparations. Career development is an ongoing lifelong process. During the career development process, students remain open to new career ideas and possibilities. Counselors and teachers build readiness for future career planning. Students build visions of what they desire to do in their lives as they contribute to the society.

    Need for Elementary/ Middle school Career Development

    Since most elementary and middle school students have limited understanding of how school relates to work, students use career development curriculum to build a foundation and the connection between career development, Twenty-First Century Skills, school academic subjects, potential careers, and future training options. As a result, students build self – awareness, possess intrinsic motivation, build a positive self-concept, and begin problem solving about career choices.

    Benefits of Elementary/ Middle School Career Development

    Elementary/ middle school career awareness lays the groundwork for future career exploration by helping students achieve the following goals:

    • Knowledge of personal characteristics, interests, aptitudes, and skills
    • Awareness of and respect for the diversity of the world of work
    • Understanding of the relationship between school performance and future choices
    • Development of a positive attitude toward work

    Students who complete career development activities have the following positive outcomes:

    • Expanded understanding of the world of work leading to an openness to an increased number potential careers
    • Improved skills to make informed decisions and complex career information problem solving
    • Enhanced academic, personal, and teamwork skill development
    • Amplified career awareness, self-esteem, sense of direction, motivation to persist, clearly defined goals

    Eventually, as students participate in career curriculum programs, the number of dropouts is minimized.

    Elementary/ Middle School Career Education Models

    There are 4 major career development models:

    • National Career Development Guidelines
    • 21st Century Skills
    • New Jersey Core Curriculum Content Standards
    • Missouri Comprehensive Guidance Program

    National Career Development Guidelines

    The National Career Development Guidelines (NCDG) determine career development knowledge, skills, and decision-making processes. The NCDG Guidelines have three domains, goals, and mastery indicators.

    The three domains are:

    • Personal Social Development (PS)
    • Educational Achievement and Lifelong Learning (ED)
    • Career Management (CM)

    The learning competency stages are:

    • Knowledge Acquisition (K). Students at the knowledge acquisition stage expand knowledge awareness and build comprehension. They recall, recognize, describe, identify, clarify, discuss, explain, summarize, query, investigate and compile new information about the knowledge.
    • Application (A). Students at the application stage apply acquire knowledge to situations and to self. They seek out ways to use the knowledge. For example, they demonstrate, employ, perform, illustrate and solve problems related to the knowledge.
    • Reflection (R). Students at the reflection stage analyze, synthesize, judge, assess and evaluate knowledge in accord with their own goals, values and beliefs. They decide whether or not to integrate the acquired knowledge into their ongoing response to situations and adjust their behavior accordingly.

    An example of the Personal Social Development domain is:

    • PS1.K2 Identify your abilities, strengths, skills, and talents.
    • PS1.A2 Demonstrate use of your abilities, strengths, skills, and talents.
    • PS1.R2 Assess the impact of your abilities, strengths, skills, and talents on your career development.

    21st Century Skills Model

    The 21st Century Model and Skills is the collaboration of the efforts of education, business, and government organizations. These organizations create a 21st Century Learning Framework that outlines the essential learning, innovation, technology, and career skills necessary to be successful in the today’s workplace. A rich, well-designed learning environment promotes creating, applying, remembering, analyzing, understanding, and evaluating processes. The 21st Century Model seeks the development of knowledge, skills, motivations, values, attitudes, beliefs, feelings, health, safety, resilience, and other qualities.

    The three major 21st Century Model main skill areas are:

    • Learning and innovation
    • Digital literacy skills
    • Career and life skills

    Within the Career and Life Skills area, the focus is on:

    • Flexibility and adaptability
    • Initiative and self – direction
    • Social and cross-cultural interaction
    • Productivity and accountability
    • Leadership and responsibility

    New Jersey Core Curriculum Content Standards

    The New Jersey Department of Education Content Standards connect the 21st Century Model and elementary/ middle school career awareness.

    • In K-5 grades, students learn the interrelationship between 21st Century life skills and personal, academic, and social development. Curriculum areas range from career awareness information and to basic personal financial literacy skills.
    • The development of 21st Century life skills and personal financial literacy continues in the grades 6-8. Students explore careers, academic and personal interests and aptitudes.

    The New Jersey Department of Education has four career education standards:

    • Standards 9.1, 9.2, and 9.3 cover life and career skills within the K-12 curriculum.
    • Standard 9.4 includes specialized, career and technical education program skills in grades 9-12 curriculum.

    These standards cover the following areas:

    • Career Awareness (grades K-4)
    • Career Exploration (grades 5-8)
    • Career Preparation (grades 9-12)

    An example of one of the objectives is:

    Standard 9.3 – Apply knowledge about and engage in the process of career awareness, exploration, and preparation in order to navigate the globally competitive work environment of the information age.

    Examples of Standard 9.3 are:

    • 9.3.4.A.4 Identify qualifications needed to pursue traditional and nontraditional careers and occupations.
    • 9.3.4.A.5 Locate career information using a variety of resources
    • 9.3.4.A.6 Explain why knowledge and skills acquired in the elementary grades lay the foundation for the future academic and career success

    Missouri Comprehensive Guidance Program

    The Missouri Center for Career Education (MCCE) is a career and technical education curriculum, research, professional development, and innovative instructional resource center.

    The Missouri Center for Career Education (MCCE) Guidance Lessons (Strands) are:

    • Academic Development
    • Career Development
    • Personal and Social Development

    Within each Strand CD: Career Development area, the Big Ideas are:

    • Big Idea: CD.7. Applying Career Exploration and Planning Skills in the Achievement of Life Career Goals
    • Big Idea: CD 8. Knowing Where and How to Obtain Information about the World of Work and Post-secondary Training/Education
    • Big Idea: CD.9. Applying Employment Readiness Skills and the Skills for On-The-Job Success

    The Big Ideas serve as the foundation for building curriculum concepts and behavioral objectives.

    Examples of CD.7 Big Idea are:

    • Compare interests and strengths with those of workers in the global community.
    • Describe occupational changes that have occurred over time within the six (6) career paths.
    • Describe the self-satisfaction that comes from completing a work responsibility.

    Tips for Finding the Right Elementary/ Middle School Career Development Program

    Based upon the National Career Development Guidelines, 21st Century Skills, New Jersey Department of Education Content Standards, and Missouri Center for Career Education (MCCE), the key elements of career curriculum provide information on the relationship between job interests, key characteristics, college majors, hobbies, abilities, and related careers.

    Teachers and counselors know that students:

    • Are curious
    • Love colorful, multimedia presentations
    • Use colors to improve attention span, concentration, memory skills, and understanding
    • Use their senses and imaginations in career exploration

    Counselors and teachers utilize career awareness programs to help students:

    • Discover career interests
    • Build awareness of career interests, abilities, skills, and values
    • Search for meaning, purpose, and direction
    • Discover potential careers that are linked to children’s identified interests
    • Understand the relationship between education, training, and specific occupations
    • Search for tools that will help students plan for the future and unlock their potentials
    • Clarify thoughts, integrate new knowledge, and promote critical thinking
    • Receive new information so that the concepts are more thoroughly and easily understood
    • Hold attention and absorb information

    Elementary/ middle development curriculum includes career tests, assessments, games, web sites, and books. Programs should be fun, educational, and not boring. Career development program are:

    • Eye appealing
    • Easy to use
    • Full of resources
    • Suitable for your students’ needs

    An effective career education tool motivates your students to explore careers. Creative career tools build a foundation for more detailed career exploration. Career development lessons should answer the question “Who am I?” and “What should I do as an adult?”

    With the right resource, students are ready and willing to:

    • Explore
    • Investigate
    • Learn
    • Ask questions
    • Enjoy discovering who they are
    • Gain knowledge, wisdom, and understanding

    Steps to Select the Right Elementary/ Middle School Career Development Program

    How do you choose the right career awareness program? Look at 3 major areas:

    • Format
    • Cost
    • Resources

    When you look at a career education curriculum, ask yourself the following questions:

    • What do your students prefer?
    • What is your budget for the curriculum?
    • What resources do you have? Do you have a computer lab?

    Then, follow these steps:

    • Select an elementary/ middle school career awareness program that your students are interested in and that provides valuable information about careers and your student’s interests.
    • Look for career development lessons that use well-known career models.

    As students grow older, the students will continue to use career models to eventually expand their knowledge of self, careers and college majors.

    In summary, when they use career education curriculum, students:

    • Learn and apply the academic material
    • Know and value self
    • Build self-esteem and confidence
    • Identify interests and build relationships between the school environment and the work force
    • Incorporate academic career pathways into classroom activities
    • Build academic, communication, problem solving, and social skills
    • Increase awareness of the need for future jobs skills
    • See the connections between learning in school, academic skills, job related skills, and careers
    • See career possibilities
    • See themselves as a future contributor to the job force
    • Receive empowerment
    • Build self-determination

    As a result of completing the career development lessons, students have:

    • Higher grades
    • Higher academic achievement
    • Improved school involvement
    • Increase in career awareness exploration, personal, and interpersonal skills

    References

    Missouri Comprehensive Guidance Program. (2011). Strands, Big Ideas & Concepts. Warrensburg, MO: Author. Available online: http://www.missouricareereducation.org/index.php?view=project&project=guidelsn. Access date: October 3, 2011.

    National Occupational Information Coordinating Committee (NOICC) (1987). National Career Development Guidelines. National Occupational Information Coordinating Committee, 2100 M Street NW, Suite 156, Washington, Dc 20037.

    New Jersey Department of Education. (2009). NJ World Class Standards Content Area: 21st-Century Life and Careers. Trenton, NJ: Author. Available online: http://www.nj.gov/education/cccs/progressions/9/. Access date: November 10, 2011.

    Trilling, B., and Fadel, C. (2009). 21st Century Skills. Learning for Life in Our Times. San Francisco, CA: Jossey-Bass.

    Dr Mary Askew specializes in career tests, websites, and books for students. Students need eye appealing, easy to use, yet comprehensive career resources. Find out how students can reach their career potentials at http://www.hollandcodes.com. Contact Dr. Askew at learning4life.az@gmail.com.

    Article Source:
    http://EzineArticles.com/?expert=Mary_Askew

    Comments Off
  • For years there has been a public outcry to “fix” the PUBLIC educational system of the United States. First of all, this will be impossible, because “fix” cannot be defined.

    Some say that “fix” means to have better and more modern buildings. Some say to “fix” mean to pay teachers more. Some say to “fix” means to have our students pass progress tests. Some say to “fix” means to be able to have our students more effectively compete in the world arena of science and business. Some say to “fix’ means give our students a better education in the basics of reading, writing, and math. Some say to “fix” means to give our students a more progressive, liberal education so they can live fuller and more complete lives. Some say we need to “fix” the educational system so students can choose what “they” want to do in life sooner and enter college with direction and focus. And the reasons for “fixing” the “broken” PUBLIC educational system go on and on.

    I think the PUBLIC educational system is broken and cannot be fixed. The system is so bogged down in political bureaucracy, red tape, special interests, union politics, under funding, misuse of funds, misdirection, non-focus, status quo thinking, social rhetoric, unfunded programs, broken political promises, and under staffed, under qualified, and under paid administrators and teachers that the PUBLIC educational system can never be fixed. It is an impossible task.

    It is no wonder that PRIVATE schools, alternative learning programs, home schooling, and online curriculums are becoming more and more popular with the “affluent” of our population. If you can afford a good education for your student, parents are pulling their students out of PUBLIC schools and enrolling them more and more in private programs of education.

    It is my opinion and the opinion of many concerned citizens that from elementary school to college, our educational system, at its best, often drives the natural love of learning out of our kids and replaces it with such “skills” as following rules, keeping still and quiet, doing what is expected, cheating or procrastinating. And that’s why, in most schools, being on time and sitting quietly are more important than critical thinking and innovative production. To prosper in this economy, students need to develop and master different skills – lifeskills such as resourcefulness, curiosity, innovation, as well as logical and verbal proficiency.

    Most progressive educational professionals would agree with Bill Gates who told our nation’s governors last year that the traditional urban high school is obsolete.

    The reality of education is that the system for the most part is outdated, too expensive, and ineffective. Many educationally progressive countries offer PUBLIC funding for education from Kindergarten through University, where as in the United States most states don’t offer Kindergarten classes, and all Public Education stops at the end of High School.

    The primary reason we send our children to school is to enable them to choose the career of their choice, earn a good living and enjoy all that life has to offer. We all want to give our children the opportunity to prosper and provide well for their families.

    Here is what has to be done if we are to give our citizens a better education which in turn gives our country more productivity in the world economy.

    1. We need to PRIVATIZE all education in our country.

    2. Education will be “funded” but not controlled by our government.

    3. Each family will be given a certain amount of money (voucher) for each student of each age.

    4. Parents can use this voucher to educate their students as they choose at any school or institution of their choice.

    5. The government has NO say in the choices parents and students make. Our tax dollars only go to “fund” PUBLIC education in the PRIVATE sector.

    6. When schools and institutions are made to “compete” for tuitions based on the performance of the teachers and educators, the quality of education will increase. If schools don’t offer parents and students a quality education, parents and students will go some place else, and the school is out of business.

    7. We need to also include a government funded college education or trade school education for all who want it. Most parents can’t afford to send their students to college. Only about one in 17 (5.8%) young people from the nation’s poorest families, those earning less than $35,377 a year, can expect to earn a bachelor’s degree by age 24. For those from the nation’s wealthiest families, those who earn about $85,000 or higher, it’s better than one in two (50%.) This University funding would also be on a voucher basis also. There would still be private colleges who might not need the money (vouchers), but for the most part most colleges would welcome the money as a way to increase enrollment and increase the quality of the education they offer.

    8. The obvious results of PRIVATIZING education is that not only schools would have to compete to get the student, by offering a quality educational program, but teachers could now offer their services in a FREE market. The fact is, the good teachers would be paid more. Schools would have to offer the good teachers more to keep them. If a good teacher could make twice as much at another school, because they are better qualified and had a “parent following,” schools would have to get serious about offering teachers more money. More people would want to become teachers if they could get paid more. And just like in every business, in order to get the best, you have to pay them more.

    9. Online schools would become more and more popular and accepted also. This is especially great for the “inter-city” areas and “rural” areas, where education has been hard to fund, and quality teachers hard to find.

    10. On the “one student, one voucher” system, all communities are now able to compete equally for the best teachers and educators. Because of population (demand) in large cities and communities, some schools would have to hire more teachers. In the small cities they would need fewer teachers, but the “money” is the same per student.

    11. By PRIVATIZING education, funded by the government with our tax dollars (as we currently do) we would be able to save money. The United States could keep the PUBLIC education budgets at a manageable level. Schools would have to compete for the funding and just like the “price wars” of car dealers, furniture stores, and all businesses, schools would have to continually strive to give parents and students “MORE education” for their money. This is Capitalism at its best.

    12. The less government “control” of our PUBLIC education, the better. Government would have NO say or control whatsoever on the type of education parents chose for their students. Government would only FUND educational choices based on the government’s education budget. The PRIVATE sector would have to compete just like any other private business for the money by offering a better, quality education to its customers (the parents and students.) The PUBLIC education system for the most part now is a MONOPOLY and doesn’t have to “try harder.” Just like the deregulation of the airlines, the telephone companies, etc., prices would go down (or in this case stay down) based on the economic rule of supply and demand. PRIVATIZING our PUBLIC education answers ALL the problems we currently face in our current PUBLIC education system.

    Larry John is the international author of Think Rich to Get Rich, a detailed outlining of the 4 pillars of wealth, and Larryisms, an introduction to pragmatic thinking. He owns a successful advertising agency and enjoys his many entrepreneurial plots and adventures. He is also the founder of The Pragmatic Thinker found at ThePragmaticThinker.com

    Article Source:
    http://EzineArticles.com/?expert=Larry_John

    Comments Off
  • Due to the growing number of double-income families in America, the need for childcare providers is constantly on the rise. Just take a look at the statistics: According to the U.S. Department of Labor, in their May 2005 Databook, 11.6 million children under age 5 were in some type of regular childcare arrangement every week.

    In the 2004 American Community Survey conducted by the U.S. Census Bureau, a whopping 63% of children under age 5 are in some type of regular childcare arrangement every week.

    How does this impact our society in general?

    These statistics show that more than half of preschool-age children spend a majority of their waking hours in the care of non-family members. According to records, these children spend an average of 36 hours per week in a private or public childcare facility.

    These figures become significant when we consider that the first few years in a child’s life are the so-called ‘formative years.’ These are when kids’ brains imbibe a lot of inputs from his environment. Thus, the people with whom he spends much of his waking hours impact his development significantly.

    And because childcare is inevitable for double-income families, single parents, and couples who don’t have the luxury of having other relatives to look after their children, childcare providers must be selected with great care.

    Quality childcare is important so that the child will be positively influenced intellectually, morally, and socially. A well-trained childcare workforce is important so that the kids left in childcare would eventually perform well in academics as well as have fewer behavioral problems as they grow up.

    Childcare facilities must provide quality programs that are both safe and enjoyable for their wards. This means that the overall environment in a childcare center must come as close as possible to the environment that the child has in his own home – surrounded by caring adults who are deeply concerned in his welfare.

    Many childcare agencies aggressively encourage childcare providers to obtain early childhood education courses, or at least enroll in continuing childcare education [http://www.bestchildcareguide.com/category/infant-day-care-centers], so that they come well equipped with the knowledge and skills necessary for their jobs.

    Even as some teenagers and working students are found worthy to be excellent childcare providers, studies made by the Center for the Childcare Workforce show that the amount of formal education possessed by a childcare provider is still the strongest predictor for his or her ability to facilitate developmentally appropriate activities for children under his or her care.

    You can also find more info on child care and childcare center [http://www.bestchildcareguide.com/category/a-childcare-center]. Bestchildcareguide.com/ is a comprehensive resource to know more about child care.

    Article Source:
    http://EzineArticles.com/?expert=Jonathan_Andrew

    Comments Off
  • Impressive Gourmet Foods

    Joining a creative cooking school will teach you the necessary skills you need to prepare gourmet foods. There are many different gourmet foods you can learn to cook, such as gourmet meats, seafood, coffee, chocolate, and more.

    Hard to Find Meats

    Gourmet meats are especially popular finer gourmet foods and this includes ribs, pork chops, and smoked turkey, just to name a few of the many you can choose from. Gourmet meats can be implemented into meals all throughout the day, and there are various cuts of gourmet meats, which differ in terms of their tenderness and flavor.

    If you do live in an area that has a great supply of gourmet meats make friends with the in house butcher. Tell him what type of event you are planning and how many people will be attending. He will be able to furnish you with all the information about the type of meat and its cost that you can serve to your guests that is sure to impress. Locating Gourmet Coffee

    Finding that perfect cup of gourmet coffee amongst the myriad of brands available can be a tedious task. The flavor is contingent upon many factors. They type of bean and where it is grown, the way it is shipped and packaged, how fine the grind and finally brewing method.

    Starting or finishing a meal of finer gourmet foods with a cup of gourmet coffee is adamant. If you have spent the time and extra money on the main course you will also want to serve the most flavorful cup of java. Starting with a flavored coffee and ending with a cappuccino or espresso is recommended.

    Finally the Chocolate

    Of course no talk of finer gourmet foods would be complete without discussing gourmet chocolate. Everyone loves chocolate, and in fact there are very few foods in history that are as highly prized as chocolate.

    Gifts of gourmet chocolate truffles, fudge, dipped fruits etc., are all highly prized by the recipient. They can be found online and shipped directly to your friend or loved one.

    Searching for finer gourmet foods can be done easily online. They can be shipped conveniently to your front door and added to your next gourmet meal or dinner party menu. Whether you are looking for gourmet meats, coffee or chocolates it is always worth it to take gourmet cooking classes. The the extra time and effort will definitely pay off with the compliments you will receive.

    Find the latest information on Creative Cooking School as well as Cooking School.

    Article Source:
    http://EzineArticles.com/?expert=Steven_Milstone

    Comments Off
  • Making money because of affiliate company internet marketing, aka “affiliate marketing” can be one of the uttermost gratifying endeavors you could ever begin. What’s great about this endeavor is that men and women can join and build their way to massive profits. Affiliate company internet marketing has been known to be an inexpensive, assessable system of achieving long-term profits. In reality, you can begin even with a limited budget. And with affiliate company internet marketing, you possess the advantage of working at home and experiencing the liberty and power of working for yourself.

    But there are also various people who failed in this type of business. It could be because they lack understanding and tactics. If you are a web site owner and you desire to join in an affiliate company internet marketing business, you have to understand where to find great programs.

    Clickbank, The Premier Affiliate Company Internet Marketing Program

    Clickbank is a model site to begin. Here, you can discover one of the largest affiliate company internet marketing programs in the world. You simply need to visit their site, CLICKBANK and obtain a Clickbank ID. From Clickbank’s home page, advance to “Earn Commissions” and scan for the products and services that completely fit your goals. These products are normally positioned according to their reputation.

    Clickbank is one of the affiliate company internet marketing programs that assists as a 3rd party between the web merchants and the affiliate company internet marketing associates. It is accountable in providing the technology to deliver the vendor’s offers and campaigns. The affiliate company internet marketing manager also does the job of gathering commission fees from the vendor and giving it to the associates involved in the program.

    Clickbank provides you a large and successful organization of publishers or affiliates to tap into. To be more definite, Clickbank has more than 100,000 affiliate company internet marketing associates who are experts in locating targeted clients for your associate program. The explanation for why a large number of affiliates are becoming a part of Clickbank is probably because gaining commissions in this organization is absolutely fair and clear.

    Becoming a Clickbank Affiliate Company Internet Marketing Vendor

    For most people, applying for an account with Clickbank is so simple. All you have to do is sign up at their site for free and they will begin to sell your products. Maintain a web site that provides your potential customers detailed information about your offered product or services. At your website, you must also maintain a comprehensive technical support pages for your product. In return, Clickbank will promote and sell your product, give customer service for your product, allow their affiliates to pass on traffic to your web site, enable you to encourage new affiliates to advertise your web site, furnish real-time sales reporting for you and the affiliates and send you and all affiliates a paycheck twice a month.

    Becoming a Clickbank Affiliate Company Internet Marketing Associate

    If you’re a future affiliate company internet marketing superstar, you definitely will not have a problem becoming a participant of this network. First, you will need to place their link on your website and if you don’t possess a Clickbank account, you will want to complete the extremely simple affiliate company internet marketing registration form and create your own Clickbank account. Then, after you have created your username, you are at liberty to select whatever merchandising tools you desire to use in order to bring in more clicks and create more sales. After selecting business tools, you can now get your associate link.

    That’s how easy it is to join Clickbank. But becoming a Clickbank super affiliate is no minor achievement. It means you need to possess the power to sell lots of affiliate merchandise. You also want to have knowledge in search engine optimization, email marketing, ezine marketing, reciprocal linkage, link exchanges and other systems of promoting your affiliate company internet marketing program.

    Becoming an Affiliate Company Internet Marketing Superstar

    Amidst the secrets to become affluent in affiliate company internet marketing is to come up with great content based website and put your associate links in all your content. Your primary objective here is to present your visitors with great quality content concerning the things they are engrossed in. Set aside the job of selling. It should be done by the sales letter page you are directing them to.

    Promote multiple affiliate programs in your website but don’t promote everything the planet has to sell. Just select the affiliate company internet marketing programs that fit your site and concentrate on them. Then, it is smart to automate the entire process, giving you ample time for different ventures. Yes, automation is another key to becoming a top affiliate company internet marketing associate.

    Of course, you have to expend more time in reading, learning and taking up the changes in affiliate company internet marketing business. Because of this, you’ll stay on top of the trends. If you are familiar with online marketing, you’ll realize how critical it is to stay up-to-date. In this type of business, what worked and what was accepted few months ago may not work at present-day. So always see to it that you comprehend what’s new in affiliate company internet marketing day-to-day.

    Affiliate Company Internet Marketing Can Be Your Financial Vehicle

    Even though it can genuinely be hard work becoming a super affiliate, you shouldn’t give thought to quitting. Keep in mind that in affiliate company internet marketing business, you want to develop perseverance, self-control and knowledge. These traits will enlighten you to carry on no matter how difficult the job is. Also, check your affiliate company internet marketing statistics. This will help you find out what is working and what is not. Make important changes if required but do it one at a time and be patient.

    Don’t forget that in affiliate company internet marketing, everything won’t take place immediately. And it will not occur without blood, sweat and substantial time commitment. Again, simply encompass patience, persistence and knowledge; then do above mentioned tactics. Once you know it, you will begin gaining profits. Trust me, the benefit of all your efforts here in affiliate company internet marketing shall be way too sweet.

    Richard Trice has been marketing online since 1999 and has sold millions of dollars worth of products. You can Discover the #1 Weapon that is responsible for his success at The Real Secret to Massive Online Success! [http://www.guerillamarketingtool.com/affiliate2]

    Article Source:
    http://EzineArticles.com/?expert=Richard_Trice

    Comments Off
  • In the automotive employment market there are still very attractive job opportunities available all over the world. So if you are in the automotive employment market and want to make a change there are still a lot of opportunities all over the world.

    In this modern world there do exist a massive shortage highly skilled automotive technicians all over the world. So if you are a highly skilled auto technician you can choose where you want to work in the world.

    By just applying on one of the many automotive recruitment companies web pages, and they will search a job opportunity for you any place in the world. The fact is that a lot of emerging automotive markets have opened up in reasoned years, due to the power shift in the automotive industry.

    This automotive employment market is going to become even bigger in the future as all new type of cars is going to hit the market. Like all the “EV” cars that are still in the prototype phase. All these cars will have new technology implemented into them, so new personnel must be trained to work on them in the future.

    This will bring a paradigm shift into this automotive employment market, even the training methods and the skill sets that must be trained have to change in the very near future.

    This will cause the manufacturers to start running extensive training and develop programs, to have highly skilled technicians to assist them to establish their brand. There will be coming new brands and brand name into the playing field and these brands will need to still build their names in the market place.

    To build a brand name you need a powerful after sales service you can assist your customers with. This alone will create a new automotive employment market to the auto industry; just imagine an electronic or chemical engineer working at your local car dealership.

    It may sound farfetched but it is possible as the cars in the future will be driven with power plants like fuel cells, hydrogen emission and electric motors. All of this is going to come to the market place in this modern world sooner than most of us do realize. So the predictions are that a big portion of the existing automotive workforce will leave.

    They will leave this workforce as they are from the old school with old school principles that will become extinct with this new technology. The human tendencies are that you will stay ignorant if you become a member of the old school club. This only happens as the older people were conditioned that they can only learn something up to a certain age. All of us know this is not true but the system wants them to leave as it is harder to change and old horse to get rid of his or her habits

    The system was created to develop a group of slaves that would be easier to condition, into what this slave system needs and not what the workers needs. That is one of the reasons why the older leading hands in the automotive employment market gets removed or retrenched. The general modern business conceptions are that older people are resisters to modern business, as they don’t want to change.

    If all this highly skilled people are removed in the future the whole automotive industry will suffer a massive skills and brain lost that could have passed on to the younger people. Findings are that most of this older people in the automotive industry don’t want to share their knowledge and skills anymore, because they don’t see themselves as resistors for future development in the automotive industry.

    So the automotive employment market will suffer great losses in the near future, due to this phenomenon.

    About The Author

    Rocco van Rooyen is an Author on Automotive Solutions. As an Entrepreneur and Author on the subject, he is at the forefront to provide solutions to all automotive related problems.

    For more articles (or training) on Automotive employment or to get your FREE Mini Course to How to manage your Automotive Solutions go to http://automotivesolutionsforall.com.

    Article Source:
    http://EzineArticles.com/?expert=Rocco_Van_Rooyen

    Comments Off
  • A domestic animal must know how to adapt itself to live with you together; from one side, preserving it’s originality, and from the other side, don’t be a burden or source of problems for your home. In order to keep this in balance you need to blockade a cat’s bad behaviour. And the best thing you can do with this is preventive measures.

    Scientists emphasize five types of the common problems, which you can meet during your cat’s upbringing and training.

    Cat behavioural problem 1

    Capricious and aggressive cat, which does everything it wants.

    Sources of such behaviour come out from its childhood, when it didn’t know word: “NO!” or “DON’T!”

    What to do with this? You need to take your kitten or adult cat to your hands more often. And never kick it! Because this will not help, only will make cat angrier. If cat shows its claws – stop playing and caressing it, and say: “NO!” or “DON’T!”

    You should remember, that a cat’s belligerence very often caused by fear.

    Sometimes you may meet spitting cats. You may respond to this cat’s bad behaviour the same way – spitting upon it! If this does not help, take sprayer – this method definitely helps.

    Sometimes cats behave very aggressive, scratching your carpets, and it seems they are trying to bury something. It can come from feeling that cat lost control upon situation. In this case – you may propose old rug to your cat. Or wrap cat in warm towel. It works, because warmth reduces fear, as well as love and caress.

    The second possible cause of such an aggressive behaviour – cat’s territory protection. It happens more often in places, where live more than one animal. In this case – you need to teach patiently your pets to get accustomed to one another. And in no way lock them up. In the worst case scenario – spray them, using the same perfumes.

    Cat behavioural problem 2

    “Silly” cats, that refuse using litter box, drag off things from the table.

    In this case – the first thing is – to think about medical issues with your cat. If everything is fine and cat’s health in a good condition, think it over, whether your cat lives well in your house. Maybe cat, doing all of those things, just trying to catch your attention, because cat angry, lonely or unhappy! In this case the first measures it is love and care! Coming home after work – first thing you need to do is caress your cat and communicate with it! And only after that – socialize with the rest of your family!

    Also cats don’t like people, who they are afraid of. And because of this – cats do mark in front of those people. In this case, I advise you to hang up the foil, where you wrapped the fish, over the cat’s favourite place, where cat does marks. This method will distract cat’s attention to do the marks on the floor. Or you may try to feed your cat in that place, where cat urinates.

    If you can not find out about motives of such behaviour, glue the sticky tape around that “special” territory, or spray with vinegar around it. And you don’t need to poke your cat’s nose into that mess – it doesn’t work every time! Also consider to set up litter box very comfortable for your cat to use.

    Cat behavioural problem 3

    You have a “whining” cat.

    Maybe, the first thing you will want to do is to take cat to your hands and caress it! And the second thing, which comes to your mind after few hours listening to the cat’s howling – is to kill your pet! Of course, if it is not the disease, you need to know – cat is whining, because it feels abandoned. What is the solution to this behavioural problem? You need to provide comfortable place for your cat, according its taste. Make such a place well beforehand cat’s “concert”, and if cat starts whining at night anyway – spray cat with water.

    Cat behavioural problem 4

    You have cat – destroyer.

    Representatives of this type trying to tear everything that could be found on their way. In this case you must hold your temper and all your patience! Cat will not understand from the very first time that it is not allowed to tear to pieces everything in your house. You need to have special plank for cat to scratch. Any plants, which cat doesn’t like and always pull out you need to keep in a safe place, not reachable for the cat. It is better to make special garden for your pet only. The most elementary “cat’s garden” – is oats in the pot. You may grow wheat or parsley as well.

    Cat behavioural problem 5

    You have cat who is “prima donna”.

    Main symptoms – cat eats with you at the same time, but only the best pieces of meal, you have prepared for yourself! And cat allows you to care about it graciously. Saying that, your cat is a snob. What do you need to keep in mind? Most of the cats can change their diet during just a few days, of course, if you think that it is the best and only choice. Cats can even go without food for few days – nothing terrible will happen!

    Measures for changing such a behaviour: don’t feed your cat from your plate; you need to camouflage new cat’s food to its favourite food, increasing the dose. You need to harden your heart, because that time cat will be looking at you with beseeching eyes! Feed your cat strictly by appointed hours. You may even ring the hand bell before feeding time and caress your pet as often as possible.

    Author – a professional and enthusiast with wide experience in training cats and dogs. To learn more about how to train your cat successfully and correct it’s behaviour visit The Planet of the Cats where you will find useful information and vital links to all your answers about cats and kitten training, dietary solutions, and vet advice: http://catsplanet.wordpress.com.

    Article Source:
    http://EzineArticles.com/?expert=Sergey_M

    Comments Off
  • Marketing online and offline couldn’t be more complex and competitive than it is today. Markets have fragmented and advertising mediums have splintered into hundreds of specialized niches, all requiring specialized expertise in order to achieve respectable results. Marketing channels too, are splintered and controlled by conglomerates. It’s a realm that is often beyond the average marketers view let alone their ability to control it.

    Promotional marketing is generally seen as the tail end of the campaign, however if a companies overall marketing activities don’t support its objectives and timing, the results are often poor, and the promotions manager gets to take the blame for the failure.

    Choosing a good marketing company to integrate these complicated promotional channels is a task in itself since many will promise exceptional marketing campaign results yet few will deliver what you expect. When they fail, will you know where the problem was or will you have to chalk it up to experience and start all over again?

    Why is it that many marketing firm’s promotional programs and implementation fail? Primarily because they don’t understand this fragmentation of media. Integrated marketing isn’t just a buzzword. Multi-channel marketing tactics need to be developed and coordinated by a campaign manager and carried out as a systematic program. Unfortunately, there is a shortage of skilled promotional marketing experts and a limited number of marketing companies that have a national network of marketing channel partners and contacts. Integrated marketing can’t be done well by small marketing companies that arrange deals with other independents. Large marketing companies have the resources, and the network of established channel partners that ensure your products are promoted from distribution to point of sale.

    Marketing Promotion

    Since marketing and advertising channels have become so fragmented, it is difficult for an advertiser to reach and affect a target consumer. Advertisers can no longer take access to consumers for granted and it takes a concerted effort to reach a consumer a number of different ways. Promotional marketing campaigns have to consider multiple mediums including the Internet to achieve optimal promotional and sales results. When they work together, they can register with the consumer audience, and ensure that your products are distributed to where they need to be at the right time.

    We hear a lot about Internet marketing and its incredible reach, and it is excellent for communications and setting up brand awareness and purchase desire. However, for consumer goods companies, few promotional channels surpass retail store promotion. The retail store location is where the sale is made, and when your promotional program is focused to work well here, you’re likely to see things go well. A sale can be lost at the point of sale, much to the consternation of firms with weak connections and retail sales training programs. They’re unable to respond to sales rep issues and the demands of consumers, and when the consumer loses confidence or interest, they won’t commit to buying the product.

    Sales transactions are complex and premiums and incentives are a key part of whether your product will make it to the store shelves and receive the right sales support. Once your products leave the warehouse, they’re on their own, unless a professional promotional marketing company is supporting them at the retail level.

    Strong Integrated Channels

    Marketing channels are complicated too, and if the connections in your network aren’t strong throughout, your sales can come to shuddering halt. Don’t think marketing channel members don’t know about your distribution vulnerabilities too. They know you’re an independent and they have their primary loyalties to bigger manufacturers and distributors. Your products may get secondary status and receive no sales support.

    So what happens during fragmented promotional campaigns? Many marketing promotion campaigns are marred by poor point of sale signage, supplier communication blocks, unreliable reporting, warehouse fulfillment problems, poor sales support, poor sales training, along with high costs and outdated technology. A marketing promotion can fail many different ways and you need to understand why. When you’re spending hundreds of thousands of dollars on campaign development and distribution activities, and have committed to a particular marketing company, your company’s future is on the line.

    What you need is a reliable marketing company that possesses the warehousing and database systems, fulfillment practices, and sales support network to ease distribution and communication problems.

    If you’re still managing your marketing promotion campaigns in-house, you should consider outsourcing to a promotional advertising and marketing firm that offers a complete variety of support service. From campaign planning to post-sales customer support, these companies can take a burden off your hands and actually give you an edge in the retail promotions space.

    Big promotional marketing companies have developed capabilities in producing creative and effective POS marketing materials, print advertising pieces, packaging, warehouse automation, and retail distribution. They can help you manage large scale orders on demanding deadlines because their state of the art electronic systems are set up to do this. They provide solutions for billing/invoicing, customized reporting, and warehouse distribution of your marketing collateral. From EDI transactions to Web-based reporting tools, they have a command of the marketing fulfillment process and can give you an excellent awareness of your marketing campaign performance. Just working with these companies once can make you a better marketing manager.

    So give yourself a break and bring in the full service promotional consultants and then start seeing your marketing campaigns hit the mark. As part of a complete integrated, promotional marketing campaign, these service companies will save money, time, and reduce communication problems, and thus save your future marketing channel relationships.

    The top promotional marketing firm in the US is without a doubt, Archway Marketing Services. This company has been serving marketers across the US for decades. Archway takes control of your complete promotional marketing campaign from start to finish. They provide excellent cost efficiencies in warehouse, inventory management and shipping. Their integrated ERP platform enables real-time supply management, reporting and customer care.

    If you could double the ROI on your retail promotional marketing campaign, wouldn’t it make sense to bring in a full service promotional marketing company?

    Archway Marketing Services delivers exceptional promotional marketing solutions. This top rated promotional marketing company offers a wide range of promotional marketing services including the execution of your marketing campaign fulfillment. They plan and create powerful, consumer-focused solutions, which include premiums & incentives, sweepstakes, games, contests, merchandising systems, point of sale promotions, and real time performance information on the success of your promotional campaigns.

    Article Source:
    http://EzineArticles.com/?expert=Scott_D._White

    Comments Off
  • About 25 years ago I began formulating pet foods at a time when the entire pet food industry seemed quagmire and focused on such things as protein and fat percentages without any real regard for ingredients. Since boot leather and soap could make a pet food with the “ideal” percentages, it was clear that analytical percentages do not end the story about pet food value. I was convinced then, as I am now, that a food can be no better than the ingredients of which it is composed. Since this ingredient idea has caught on in the pet food industry, it has taken on a commercial life that distorts and perverts the meaning of the underlying philosophy of food quality and proper feeding practices. Is health reducible to which ingredients a commercial product does or does not have? As contradictory as it may seem to what I have just said, no it is not. Here’s why.

    AAFCO Approval

    The official Publication of the American Association of Feed Control Officials (AAFCO) gives wide latitude for ingredients that can be used in animal foods. As I have pointed out in my book, The Truth About Pet Foods, approved ingredients can include*:

    dehydrated garbage

    undried processed animal waste products

    polyethylene roughage replacement (plastic)

    hydrolyzed poultry feathers

    hydrolyzed hair

    hydrolyzed leather meal

    poultry hatchery by-product

    meat meal tankage

    peanut hulls

    ground almond shells

    (*Association of American Feed Control Officials, 1998 Official Publication)

    Simultaneously, this same regulatory agency prohibits the use of many proven beneficial natural ingredients that one can find readily available for human consumption such as bee pollen, glucosamine, L-carnitine, spirulina and many other nutraceuticals. It would be easy to conclude that reason does not rule when it comes to what officially can or cannot be used in pet foods.

    From the regulators’ standpoint, they operate from the simplistic nutritional idea that the value of food has to do with percentages and that there is no special merit to any particular ingredient. They deny the tens of thousands of scientific research articles proving that the kind of ingredient and its quality can make all the difference in terms of health. They also are silent about the damaging effect of food processing and the impact of time, light, heat, oxygen and packaging on nutritional and health value.

    The 100% Complete Myth

    Consumers are increasingly becoming alert to the value of more natural foods. Everyone intuitively knows that the closer the diet is to real, fresh, wholesome foods, the better the chance that good health will result. Unfortunately, people do not apply this same common sense to pet foods. Instead they purchase “100% complete” processed foods, perhaps even going the extra mile and selecting “super premium” or “natural” brands, thinking they are doing the best that can be done. They surrender their mind to a commercial ploy (100% completeness) and do to their pets what they would never do to themselves or their family – eat the same packaged product at every meal, day in and day out. No processed food can be “100% complete” because there is not a person on the planet who has 100% knowledge of nutrition. The claim on its face is absurd. Understanding this simple principle is more important than any pet food formulation regardless of the merits of its ingredients. Everything that follows will begin with that premise, i.e., no food should be fed exclusively on a continuous basis no matter what the claims of completeness or ingredient quality.

    Genetics Is The Key

    Pets need the food they are biologically adapted to. It’s a matter of context. Just as a fish needs to be in water to stay healthy, a pet needs its natural food milieu to be healthy. All creatures must stay true to their design. What could be more obvious or simple? For a carnivore the correct genetic match is prey, carrion and incidental fresh plant material, and even some fur and feathers, as well as the occasional surprise of unmentionables found in decaying matter. It’s not a pretty picture to think that “FiFi” with her pink bow and polished toenails would stoop to such fare, but that is precisely the food she is designed to eat. Since that is her design, matching food to that design (minus the more disgusting and unnecessary elements) is also the key to her health.

    The Disease Price

    We may prefer to feed a packaged, sterile, steam- cleaned, dried, farinaceous chunk cleverly shaped like a pork chop, but let’s not kid ourselves, that is not the food a pet is designed for….regardless of the claims about ingredients on the label making one think it is five-star restaurant fare. Pets may tolerate such food for a time, but in the end nature calls to account. The price to be paid is lost health in the form of susceptibility to infections, dental disease, premature aging, obesity, heart and organ disease, diabetes, cancer, arthritis and other cruel and painful chronic degenerative diseases. Because our pets are not out in the rigors of nature where they would quickly succumb to such conditions and end their misery, they languish in our protected homes and under veterinary care that does not usually cure but merely treats symptoms and extends the time of suffering. That suffering begins with the way in which we are feeding our pets, not the ingredients in a supposed 100% complete pet food.

    The Perfect Food

    What is the solution? It is simple and something I have been preaching for the past 25 years. Return pets to their environmental roots. They need – daily – interesting activity, fresh air, clean water, romps in nature, lots of love, and food as close to the form they would find in the wild as possible. Fresh, whole natural foods fit for a carnivore and fed in variety are as good as it can get. Anything less than that is a compromise. Compromise the least if health is the goal. (Same principle applies to you and your family.) To get a packaged food as close as possible to that goal requires the right starting philosophy of feeding (described above) and the expertise to design and manufacture such foods.

    Enter The Profiteers

    Elements of these principles (often distorted or misunderstood) have been taken up by an endless line of pet food entrepreneurs. The low fat craze led to low fat pet foods. The high fiber craze led to high fiber pet foods. The “no corn, wheat or soy” craze led to no corn, wheat or soy pet foods. The “omega- 3″ craze led to pet foods with fish oil. The “variety” craze led to pet foods supposedly offering variety. The “four food groups” craze led to all four bundled into a package. The “raw” craze has led to raw frozen pet foods. The list is endless and the race for pet owner dollars is at a fever pitch.

    One can only feel sympathy for a concerned pet owner as they stroll along the huge array of pet food options in pet food aisles. Unfortunately, armed with only sound bites and lore they may have heard from a friend, breeder, veterinarian or on a commercial, they make choices that not only do not serve the health of their pet but may directly contribute to weakened immunity and disease.

    The first thing consumers should keep in mind is the ideal diet for pets as described above. No packaged product regardless of its wild claims is ever going to equal that. The next best thing is to home prepare fresh meals. (Contact Wysong for recipes and instruction.) If that is not always possible, then products should be selected that are as close to the ideal as possible. (More suggestions below.)

    Raw Frozen Pet Food Dangers

    At first glance, considering the perfect feeding model I have described – raw, natural, whole – the best food may seem to be one of the raw frozen pet foods now clamoring to capture the “raw” craze. I’m sorry to say that some of these purveyors even use my books and literature to convince pet owners that their frozen products are on track. They take bits and pieces of good information and distort it into something that pretty much misses the point and misleads consumers. Also, these exotic frozen mixtures of ingredients of unknown origin, manufacturing and freezing conditions are most certainly not economical nor the best choice. They may, because of the water content and raw state, be outright dangerous.

    Human Grade

    Then there are claims about “USDA approved” ingredients, “human grade” ingredients and ingredients purchased right out of the meat counter at the grocery store. Again, at first glance – and superficiality is what marketers like to deal with – it may seem that such foods would have merit over others. But such labels only create a perception of quality. People would not consider the food pets are designed for in the wild – whole, raw prey and carrion – “human grade” or “USDA approved.” Because something is not “human grade” does not mean it is not healthy or nutritious. For example, chicken viscera is not “human grade” but carries more nutritional value than a clean white chicken breast. Americans think that chicken feet would not be fit for human consumption but many far eastern countries relish them. On the other hand, “human grade” beef steaks fed to pets could cause serious nutritional imbalances and disease if fed exclusively. Pet foods that create the superficial perception of quality (USDA, human grade, etc.) with the intent of getting pet owners to feed a particular food exclusively is not what health is about.

    Pet Nutrition Is Serious Health Science

    Pet nutrition is not about marketing and who can make the most money quickly. Unfortunately an aspiring pet food mogul off the street can go to any number of private label manufacturers and have a new brand made. These manufacturers have many stock formulas that can be slightly modified to match the current market trend. Voilà! A new pet food wonder brand is created.

    Pet foods are about pet nutrition, and nutrition is a serious health matter. There is an implied ethic in going to market with products that can so seriously impact health. But the ethic is by and large absent in the pet food industry. Starting with the 100% claim and on to all the fad driven brands that glut the shelves, health is not being served. Nobody other than our organization is teaching people the principles I am discussing here. Instead, companies headed by people with no real technical, nutritional, food processing or health skills put themselves out to the public as serious about health … because that is what the public wants to hear and what sells. Never mind whether producers really understand or can implement healthy principles. The façade sells and selling is the game. Ingredients are important, true, but not less important than the expertise and principles of the producer who is choosing them, preparing, storing, processing and packaging them. Consumers place a lot of trust that nondescript processed nuggets are what consumers are being led to believe they are. Many a slip can occur between the cup and the lip. There are many slips that can occur between the cup of commercial claims and what ends up in the lips of the pet food bowl.

    Consumer Blame

    The consumer is not without guilt in this unfortunate – steady diet of processed pet food – approach to pet feeding. They want everything easy and inexpensive. They don’t want to learn or have to expend too much effort, and they want something simple to base decisions on like: “corn, wheat and soy are evil,” or “USDA approved,” or “human grade” or “organic is good.” They also want something for nothing and think they can get it in a pet food. People want prime choice meats, organic and fresh foods all wrapped up tidy in an easy open, easy pour package, hopefully for 50 cents a pound. They may even pay $1 or a little more if the producer can convince them about how spectacular their product is or how much cancer their pet will get if they choose another brand.

    Are By-Products Evil?

    In the processing of human foods there are thousands of tons of by-products that cannot be readily sold to humans. Does that make them useless or even inferior? No. Such by-products could include trimmings, viscera, organs, bones, gristle and anything else that humans do not desire. Should these perfectly nutritious items be buried in a landfill? As I mentioned above, while Earth’s resources continue to decline and people starve around the globe, should we feed our pets only “human grade” foods and let perfectly edible – and sometimes even more nutritious – by-products go to waste? How is that conscionable or justifiable for either the consumer or the producer?

    Road Kill and Euthanized Pets

    This shift to “human grade” for pet foods is partly due to a variety of myths that have gotten much stronger legs than they deserve. Lore has spread in the marketplace that road kill and euthanized pets are used in pet foods. I have never seen the proof for this outrageous claim and after twenty years surveying ingredient suppliers I have never found a supplier of such. However, fantastic myths easily get life and the more fantastic they are the more life they have. It’s the intellectually lazy way and what lies at the root of so much misery. Sloppy superficial thinking is what leads to racism, sexism, religious persecution and wars. People would like to think the world is sharply divided into right-wrong, good-evil, black-white. Marketers capitalize on this by trying to create such sharp distinctions for consumers to easily grab on to: human grade = good/all others = evil; organic = right/all others = wrong; rice = white/corn and wheat = black. Such simplistic and naïve distinctions are quick and simple for advertisers and salespeople to use to sway public opinion. But nobody stepping back and using common sense would ever think that something as complex as health could ever come from what is or is not in a processed bag of food. Reality is not black or white; it is in shades of gray. Grayness requires some knowledge, judgment and discernment before making choices. It’s a little more work but is what we all must do if the world is ever to be a better place and people and pet health are to improve.

    What To Do

    How do concerned pet owners wanting to cut through all the marketing clutter negotiate a path? It is very simple if the basic principles I have discussed above are kept in mind. Here are tips on how to implement an intelligent health and feeding philosophy:

    1. Learn how to feed fresh food. Alternate these with honest processed foods fed in variety, and complement these foods with well- designed supplements.

    [How To Apologize To Your Pet]

    http://www.wysong.net/PDFs/apology_pamphlet.pdf

    Don’t get all particular and paranoid about balancing nutrients and ingredient do’s and don’ts. Rotate, vary, mix it up and fast once in a while. Trust in nature, not some marketing hype. (Use the same principles for yourself and your family if you want optimal health as well.)

    2. If you must have human grade or organic foods for your pet, go buy the real thing at the grocery meat counter. Take it home, cut it up and feed it raw. Freeze the remainder into small meal portions and use them for subsequent meals. Don’t turn your brain off and go buy “organic” or “human grade” pet foods that for their cost could only contain hints of the real thing. Pet food manufacturers may be clever at marketing, but they are not magicians. One thing is certain; they do not buy ingredients and then sell them to you for less than what they buy them for.

    3. Use appropriately designed supplements such as Call Of The Wild™ and Wild Things™ to balance raw meals and help make them safe if you are not skilled at such meal preparation.

    4. The best raw, processed food alternative to fresh foods from the grocer is non-thermally processed dry foods – not raw frozen ones. (See Wysong Archetype™.) Use this food for alternate meals and as top dressing to heat processed foods.

    5. Check the credentials of the person making the decisions in the company whose products you buy. Don’t go to a plumber for brain surgery and don’t expect serious healthy products from business people.

    6. Steer away from brands that are pushing any particular hot buttons such as “natural,” “no by- products,” exotic ingredients (quail eggs, watermelon, persimmons, etc.), organic, omega-3, rice and the like. Although these features may bring some merit to a food (if they are put in at other than “pinch” levels), they are not an end in themselves and if the packaged food is fed exclusively can cause more harm than good.

    7. Steer away from brands that fear monger. For example, there is the no corn or wheat scam – “buy our brand; it has no corn or wheat.” (Just saying a product has “no” something is enough to scare the non-thinking public to the brand that doesn’t have the boogeyman ingredient. Profiteers know this and play it to the hilt in the pet food industry.) The truth is, grains are put in dried nugget foods because they contain the starch necessary for the extrusion process. Starch is pretty much starch regardless of whether it comes from corn, wheat, rice, potatoes, millet or whatever. Grains also help decrease the cost of pet foods. They contribute some nutrition but in a properly formulated meat-based pet food the majority of the nutritional value comes from the meat. It is true that animals may develop allergy to corn or wheat but that can happen with rice or any other grain or ingredient as well. Problems are prevented by varying the diet. That is why Wysong has developed the range of formulations it has and puts them in small portion packs so the foods can be rotated. Of all the Wysong formulations, the ones with corn are chosen on almost a 5:1 ratio over all others and are the diets we receive the thousands of raves about, even in those pets supposedly allergic to corn!

    [Wysong Testimonials]

    [http://www.wysong.net/testimonials.shtml]

    This is not to tout the merit of corn, or any grain in pet food for that matter. They are sort of a necessary evil in dried extruded foods and any of them can bring some benefit if rotated in the diet.

    8. Do not feed any product exclusively. Variety is the spice of nutrition and the road to good health.

    9. Features to look for in a packaged product would be those that bring the product close to the raw-whole-fresh-natural standard described above: active enzymes, probiotics cultures, natural preservation and protection against food-borne pathogens, proper packaging, intelligent formulation and balance, micronutrient dense, freshly produced, fresh ingredients – and the expertise to do all of this, not just say so on a package or brochure. (Some brands trying to get on the raw food bandwagon make outright false claims about “cold” processing.)

    10. The company should be able to intelligently explain what they are doing in terms of processing, packaging, product preservation and prevention of food-borne pathogens. It is one thing to simply put a certain ingredient into a food, quite another to protect it until it is consumed. For example, Wysong owns its own manufacturing facilities in order to go beyond industry standard techniques. Special portion pack, light- and oxygen- barrier bags, modified atmosphere flush and natural ingredients to prevent oxidation and food- borne pathogens are part of all Wysong products. (See technical monographs on Packaging, Antioxidants and Wyscin™.)

    11. Most important, learn. Support a company that helps you learn the truth and teaches you how to be at least somewhat independent of commercial products. Demand that producers provide proof for their claims in the form of good logic, evidence and science. Try to discern the company’s true motives, your pocketbook or your pet’s health. Learn how to go beyond The Pet Food Ingredient Game.

    Wysong R. L. (1993). Rationale for Animal Nutrition. Midland, MI: Inquiry Press.

    Wysong, R. L. (2002, June 19). Why Modern Medicine is The Greatest Threat to Health. The Wysong e-Health letter. Wysong Institute, Midland, MI.

    [The Wysong e-Health letter]

    [http://www.wysong.net/health/hl_884.shtml]

    Wysong, R. L. (2002). The Truth About Pet Foods. Midland, MI: Inquiry Press.

    Wysong, R. L. (2004). Nutrition is a Serious Health Matter: The serious responsibility of manufacturing and selling. Midland, MI: Inquiry Press.

    Wysong, R. L. (2004). The Thinking Person’s Master Key to Health (60 Minute CD Discussion) Wysong Institute, Midland, MI.

    Wysong, R. L. (2005). Comparing Pet Foods Based Upon What Matters: The First Study of its Kind in the Pet Food Industry. Midland, MI: Inquiry Press.

    Wysong, R. L. & Savant, V. (2005). The Case AGAINST Raw Frozen Pet Foods. Midland, MI: Inquiry Press.

    For further reading, or for more information about, Dr Wysong and the Wysong Corporation please visit http://www.wysong.net or write to wysong@wysong.net. For resources on healthier foods for people including snacks, and breakfast cereals please visit [http://www.cerealwysong.com].

    Dr. Wysong: A former veterinary clinician and surgeon, college instructor in human anatomy, physiology and the origin of life, inventor of numerous medical, surgical, nutritional, athletic and fitness products and devices, research director for the present company by his name and founder of the philanthropic Wysong Institute. http://www.wysong.net Also check out [http://www.cerealwysong.com]

    Article Source:
    http://EzineArticles.com/?expert=Dr._Randy_Wysong

    Comments Off
  • In the winter of 2010 I decided to pursue a private study of bowl turning. I read every book I could find and watched YouTube videos over and over before I purchased my Nova DVR XP lathe, a 1/2 inch and 3/4 inch Crown bowl gouge, a parting tool, a large scraper, a Makita right angle drill, belt sander, orbital sander, grinding wheel, Sthil chainsaw, buffing wheel, sanding discs, sand paper, CA glue, walnut oil, lacquer, beeswax, rags, wood to build a heavy duty mounting surface for the lathe and sand bags to stabilize the table. I never took woodshop nor did I have any previous experience turning bowls. I had built a 2 story log cabin in Canada and always nurtured a love for wood and trees.

    I ordered most of my turning equipment from the wood turners catalogue and have been amazed ever since on how the tools and equipment lived up to my expectations and arrived lightning fast.

    At the same time that I built my lathe table (per Nova DVR specifications downloaded from the internet), I set out to find sources for logs. I placed free ads on craigslist asking for large logs which resulted in my acquiring some very large Dutch Elm logs and some medium size Cypress logs. I also called various firewood suppliers, most of whom did not have whole logs available or wood that was favorable to wood turning. However, one tree cutter did contact me and he expressed a true love of wood and interest in helping me to find good wood. I drove out to his storage yard where I found large diameter logs of cedar, oak, pecan and massive slabs of black walnut that his father had saved and protected.

    On another occasion I stopped by a firewood yard in the foothills and looked out upon an endless supply of huge rounds of ash, oak, and species unknown. I soon had a good stockpile of logs which I stacked in the shade of an avocado tree in my backyard and loosely covered with a plastic tarp. I kept the logs off the ground with pieces of firewood and timber I had lying around. On average, excluding the black walnut which was expensive, I could fill my Ford Explorer with large chunks of wood for $40 to $60. In comparison, upon visiting stores that supply bowl blanks, I found that most resale blanks were both small and expensive. One blank could cost as much as a truckload of un-split firewood.

    Not having a garage to house my equipment, I built a small shed using plywood and a tarp to protect my work area. I use a small BBQ cover to protect my lathe within the shed. My tools are readily available from a shelf below the lathe bench.

    I purposely avoided purchasing costly equipment like a band saw or unnecessary tools like grinding guides, etc. My intention was to create natural looking rustic bowls using the least amount of equipment as possible.

    There are so many opinions on what equipment and tools are needed, how to manipulate your tools, how to sharpen your tools, what is the right wood to use, and what constitutes an acceptable bowl…I decided to just plow through it, do my own thing, and learn as I go. The chain saw, lathe, bowl gouge, sander and grinder are at the heart of everything I do.

    I began looking at other artist’s bowls in artist shops and online. I saw the most beautifully finished hollow forms sitting behind glass on shelves…only $800.00! I also found web sites with really nice bowls for sale for such a low price that I can’t imagine how the artist could pay for their turning supplies. These observations left me perplexed and, again, I just decided to do my own thing and see what happens.

    My lack of experience and utilitarian interest in bowl turning caused me to think that my work would be sneered at by seasoned professionals. And so it was to my amazement that several of my bowls, sold privately or through silent auctions, were pieces that had visible sealed cracks, surface irregularities or warped sides. That’s when I realized that I don’t need to please other artists; there are people who find imperfections most interesting and I must admit that when fruit or a salad mix is placed in a bowl with various imperfections, the overall look is very appealing. I’ve had friends remind me not to move too far away from the rustic appeal of my first pieces and I have taken their suggestion to heart.

    The Lathe

    I love my Nova DVR XP. I looked at many other models including ones that I could not afford and inexpensive ones that required moving the belt across pulleys to change the turning speed. Now that I’m actually turning bowls I can’t imagine using anything but a constant variable speed direct drive lathe that allows you to change speeds with the touch of a finger on a digital pad. This doesn’t mean that the DVR XP is absolutely perfect…large out-of-round blanks can cause my heavy work bench to jump around at higher speeds, the safety mechanism that stops the machine during a significant “catch” can kick in too easily with large blanks turning at lower speeds, and there have been minor issues like a nut coming loose inside the housing. I’ve learned to correct or work around these issues with great satisfaction. I have NOT tried the add-on support for turning bowls over 16 inches in diameter but would imagine there will be some taxing of the lathe and my work station. The DVR was under $2200.00 and was my only large ticket purchase. It was delivered by freight to my driveway and the delivery man helped me lift it onto my work station.

    Why is it so important to be able to change speed quickly? You’ll know the answer to that question when you make your first bowl. Initial gouging, finish gouging, scraping, sanding, applying a finish, buffing…you’ll use a wide range of speeds to perform all these tasks.

    Breaking the Rules

    There’s nothing wrong with being a strict disciplinarian. There’s nothing wrong with proper training and education. It’s in my nature to go-it-alone and a big part of the fun is learning as you go and experimenting with your own ideas. As an example; Everything I’ve read and watched on video about turning bowls showed mounting the bowl to shape the outside of the bowl, then remounting the bowl to shape the inside of the bowl. This involves using a faceplate and then using a chuck for the remainder of turning. I was amazed to learn that I could cut both the outside and inside without ever removing the faceplate and still NOT have screw holes in the bottom of my bowl. Why didn’t anyone mention this?

    Using firewood rather than expensive exotics, I am at liberty to increase the depth of my bowl blank by the length of screws used to secure the faceplate. I shape the outside of the bowl, including 75% of the bottom, leaving only that section of wood at the faceplate un-tooled, avoiding cutting too close to the plate. I then, without dismounting the blank, shape the rim and inside of the bowl and follow shaping with sanding and polishing. I then use a parting tool and finally a hand saw to separate the extra wood at the faceplate from the bottom of the bowl. A belt sander will level out the bottom.

    Another rule breaker involves turning green or wet wood. I’ve found that the results depend on the wood, the amount of moisture and your willingness to deal with warping issues. Available data shows that you can turn a rough version of the bowl with even wall thickness and set the bowl aside for a few months in a cool area. I’ve read that you can put the bowl in paper bags until moisture is no longer evident on the bag. I am, at this point, too impatient to wait a few months and the only time I tried the paper bag trick, the bowl was covered in mold when I brought it out.

    When I turn a damp or wet wood, one of three things occurs. 1) The bowl warps. One of my most treasured pieces was a deep warped Dutch Elm bowl. 2) Cracks develop. That’s what CA glue is for. It works fantastic and the more you learn to use it the better the results. You can hand rub fine sawdust into the CA glue-soaked crack, apply additional thin CA glue then a dusting of more fine sawdust with a light rub to even things out. You will be able to sand the filler in less than an hour. I CA glue and/or fill all visible cracks immediately during and after turning and as needed during the drying process. OK, if you want to turn precision pieces free of any defects then this is not going to work. 3) The finishing process must be delayed. Lacquer finishes will dull from the moisture. Hardening oils will lock in the moisture. Set the bowl aside until finishing can take place. Depending on the amount of moisture and type of wood this may only take a few days or a few weeks. However, I have been applying a coat of walnut oil on all my green bowls immediately after turning and sanding. I have been sanding the green bowls with 80 thru 400 grit, wiping on a coat of walnut oil, re-sanding with 220 thru 400 grit to take down any raised grain and then setting the bowl aside. The longer the bowl is set aside the more chance that the bowl will warp and, thus, you will not be able to remount the bowl on the lathe for additional gouging or lathe sanding. 4) Nothing bad happens. I’m stupefied but it’s the truth…it’s happened many times. I turn a damp bowl, finish sand it, buff it out, wipe it down with walnut oil, leave it in a cool area of the house, turning it on top of paper bags and the bowl comes out fine. I’ve even applied coats of spray lacquer shortly thereafter. Ok, the lacquer may dimple or dull if water is evident and further finishing or buffing will be required. I had two bowls develop dark dotted lines under the lacquer finish and I’m having a hard time removing them. I’m now leaning towards letting the bowls dry after sanding, with a single coat of walnut oil rubbed into the wood.

    The bottom line: other than some issues with cracks, which I repaired as needed with CA glue (fine, medium or thick), and some warping which I kept or re-tooled to remove, I’ve turned many really cool looking green bowls without any problem. I turned 3 bowls that were damp or wet in the past week. One has gone oblong, one has rim edge bumps, two are in fine condition. The two that have minor disfiguration were so wet that my face plate was opaque during turning. The two that came out normal, except that I re-turned the rim, were damp but not saturated.

    Finishing

    I’ve experimented with walnut oil, which I’m told will not go bad, various hand rub finishes, polyurethane, lacquer, bees wax, carnauba wax, buffing compounds, etc. Lacquer (3-4 coats) gives a hard glossy finish and if you wait a few weeks it will buff out like glass. I use spray cans purchased at 10$ a pop from Rocklers. It took a while to get the technique down, don’t be discouraged.

    I was buffing the lacquer finish, walnut oil finish, and/or carnauba wax finish out as early as possible but nothing can beat applying the finish and allowing it to harden or set up before buffing. I just received a Beal buffing system that I’m trying out on the lathe. It’s unbelievable! There are 3 large thick buffing wheels, a large bar of tripoli compound for taking out fine scratches, a large bar of white diamond for polishing and a thin bar of carnauba wax for finishing. I tried it on a lacquer finished bowl which had previously been buffed using a small wheel, tripoli compound and then carnauba wax. The difference between using separate wheels for each compound and the tripoli, white diamond, carnauba combination was amazing to behold. The bowl has a true glass finish.

    Most recently I have been watching Elmer Adams (now deceased) videos on YouTube. The way he finished his large bowls is to soak the bowl in a 4 part Deft clear Danish oil and 1 part Defthane solution in a tub for 12 hours, completely saturating the bowl. He drains off the oil and then applies 5 coats of the same mixture by hand, buffing out each coat with Tripoli compound; using white diamond compound and Renaissance wax on the final coat. No spray, no lacquer…People have told me that a bowl saturated in oils take forever to dry. I am going to try a more conventional approach, applying pure tung oil cut 4/1 with a thinner to promote penetration, followed by 2/1 thinned tung oil applications with 24 hour drying and sanding in between coats.

    Spending Money vs. Making Money

    My motivation for making bowls is NOT making money. However, I don’t want this hobby to be a hole that all my extra cash disappears in. I DO want to sell the bowls I make. When you first start out it seems that you’re experimenting with equipment, tools and supplies that keep piling up the charges on your credit card bill. By avoiding purchasing fancy equipment I can do without and refining the turning and finishing processes, the amount of time and effort I put into a bowl is diminishing. Once I know how to select and sharpen my tools for a particular task, how to most effectively shape and hollow out the bowl, and understand the most direct method of developing a nice finish I will have a systematic approach to creating a bowl that others will find pleasing. At this point the cost per bowl will stabilize and I should see the returns grow accordingly. OK, this isn’t a one year turn around but I’m in this for the long haul and I love doing it. I told my wife, when I retire, every bowl I sell represents a dinner for two or a night out on the town. I also intend for the returns to pay for supplies including raw wood for turning.

    Article Source:
    http://EzineArticles.com/?expert=Robert_Vincent_Johnson

    Comments Off